Can Hail Damage Solar Panels? What to Check After a Storm — and What to Document
Most hailstorms leave solar panels unharmed — but golf-ball hail can crack glass and cells, and the costliest damage is invisible from the ground. Here is what to check, what to photograph, and how insurance usually handles it.
Solar panels are built to take a beating. They sit on your roof through rain, snow, wind, and hail, and the tempered glass on a modern panel is a lot tougher than the glass in your windows. So when a hailstorm rolls through, it’s fair to ask: are my panels actually damaged — or did they shrug it off?
The honest answer is usually the second one, but "usually" is doing a lot of work there. Panels can crack, and the damage that matters most is often the kind you can’t see from the ground. Here’s what hail actually does to solar panels, what to check after a storm, and how to document it for an insurance claim.
StormFile is a documentation tool, not an adjuster or a legal advisor. This is practical guidance, not insurance or legal advice. Coverage decisions belong to your policy and your carrier, and only a hands-on inspection of your actual system can say what a particular storm did to it.
How tough are solar panels, really?
Most residential solar panels are rated to withstand hailstones up to 1 inch in diameter falling at roughly 50 mph. That rating comes from industry standard testing (IEC 61215), where panels are shot with ice balls to simulate hail impact.
In practice, that means pea-sized and marble-sized hail (up to about 1/2 inch) rarely damages a panel at all. Quarter-sized hail (about 1 inch) is right at the edge of the rating: most panels handle it, but older panels, or panels hit at an angle by high wind, can show damage. Golf-ball-sized hail (about 1 3/4 inches) and larger is where real damage becomes common — cracked glass, shattered cells, and broken frames.
- Panel age and quality. A panel installed in the last few years from a major manufacturer is generally tougher than a budget panel from fifteen years ago. Age and UV exposure make glass and encapsulant more brittle over time.
- Hail size and wind. A 1-inch stone falling straight down is the test case. The same stone driven sideways by 60 mph wind hits harder and at an angle the panel wasn’t designed for.
- Mounting angle. Panels mounted nearly flat take hail head-on. Panels tilted at a steeper angle let hail glance off — which is one reason ground-mounted arrays at a steep tilt often fare better than low-slope roof arrays in the same storm.
What hail damage to solar panels actually looks like
Solar panel damage falls into two buckets: the kind you can see, and the kind you can only measure.
Visible damage
- Cracked or shattered glass. Look for spiderweb cracks radiating from an impact point. A cracked panel can still produce power — and still be a problem, because water gets in through the crack and corrodes the cells underneath.
- Dented or bent frames. Aluminum frames bend under large hail. A bent frame can compromise the seal around the glass and let moisture in.
- Chipped junction boxes. The small box on the back of the panel where the wiring connects. If it took a direct hit — more common on ground-mounted arrays — the wiring can be damaged.
Hidden damage
This is the part homeowners miss. A hailstone can crack the silicon cells inside a panel without breaking the glass at all. These micro-cracks don’t show up in a photo from the ground, and they may not show up in your power output right away either. Over months, the cracked cells degrade, hot spots form, and output drops — sometimes by 20 percent or more.
The reliable ways to catch hidden cell damage are a drop in power output and a professional test. Compare your system’s production after the storm to the same period before it and last year — a sudden, unexplained drop is worth investigating.
- An electroluminescence (EL) test. A solar installer or inspector can run an EL scan that shows cracked cells as dark lines. This is a specialized test — not something you do from a ladder with a phone camera.
- A thermal camera scan. Hot spots from cracked cells show up as bright patches on an infrared image. Some installers offer this as part of a post-storm inspection.
If your panels look fine but your output dropped after a hailstorm, say so in your claim and ask for a professional inspection. Don’t assume a clean-looking panel is an undamaged panel.
How to check your panels after a hailstorm
Do not climb on your roof. Panels are slippery when wet, and a cracked panel underfoot can give way. Everything below can be done from the ground or from inside your home.
- Look from the ground first. Stand back and scan the array with binoculars or your phone’s zoom. Look for cracks, discoloration, or panels that sit at a different angle than their neighbors — a tilted panel may have a loose mount.
- Check the inverter and monitoring app. Most modern systems report production per panel or per string. Look for a panel that has gone dark or dropped sharply compared to its neighbors. Note the numbers and screenshot them — that’s dated evidence.
- Photograph each panel. Get a wide shot of the whole array, then zoom in on any panel with visible damage. Photograph from the same angle before and after any repair, and include a coin or ruler in close-ups for scale where you can do so safely from the ground.
- Check the roof around the panels. Hail that cracked a panel also hit the shingles around it. Photograph the roof, the flashing, and the mounting points — damage there is part of the same claim.
- Check ground-mounted systems up close. If your array is ground-mounted and reachable without climbing, inspect it directly. Photograph the front and back of every panel, the junction boxes, and the wiring runs.
- Write down the storm details while they’re fresh. Date, rough time, hail size (a hailstone next to a coin makes a great photo), wind direction, and what you heard. Keep this with your photos, not scattered through your camera roll.
Will insurance cover hail damage to solar panels?
Usually, yes — with the usual caveats. Rooftop solar panels are generally covered under a standard homeowners policy as part of the dwelling, because they’re permanently attached to the roof. Ground-mounted systems are often covered too, usually as "other structures" — but sometimes with a lower coverage limit, so check your policy.
A few things that catch homeowners off guard:
- Your panels may not be covered for their full replacement value. Some policies cover panels at actual cash value, which factors in depreciation. Others cover replacement cost. The difference can be thousands of dollars on a system that cost $15,000 to $25,000 to install.
- Your solar lease or loan may have its own insurance requirements. If you lease your panels, the leasing company usually carries its own coverage — and your homeowners policy may not need to cover them at all. Check who owns the system before you file.
- The deductible applies. A hail claim that covers a $20,000 panel replacement still runs through your deductible, which on many policies is $1,000 to $2,500 — or a percentage of the home’s insured value for wind and hail.
- Hidden damage needs proof. A cracked panel is easy to show an adjuster. A panel with micro-cracked cells and a 15 percent output drop needs production records and a professional test to support. Gather that evidence early — it’s much harder to reconstruct months later.
When in doubt, ask your agent before the storm, not after it. A five-minute call can tell you whether your panels are covered as dwelling or other structures, whether it’s actual cash value or replacement cost, and whether your deductible is a flat amount or a percentage.
Mistakes to avoid with a solar panel hail claim
- Don’t let a roofer remove the panels before the adjuster sees them. Panels often have to come off before roof work starts — but photograph them in place first, and don’t let anyone haul damaged panels away until the adjuster has seen them or you’ve documented them thoroughly.
- Don’t assume the panels are fine because they still work. A panel with cracked cells can keep producing for months while it quietly degrades. Document the output now, and keep monitoring it.
- Don’t forget the rest of the system. Inverters, optimizers, and wiring can be damaged by the same storm — and by the power surges that come with it. If your system throws an error code after the storm, screenshot it and include it in your record.
- Don’t clean the panels before photographing them. Dirt, debris, and hail residue on a panel can actually help show the storm’s impact. Photograph first, clean later.
The record, done right, while the evidence is fresh
Phone photos are a good start. A structured report takes it further: organized photos, AI-flagged visible damage with locations marked, timestamps, and a PDF you can hand to your adjuster or contractor in one file instead of scrolling through a camera roll. That is what StormFile does — $39 per report, and it documents what is visible in your photos. It does not assess damage the way an adjuster does, and it does not guarantee a claim outcome. It is a record, done right, while the evidence is fresh.
Start my report — $39The bottom line
Solar panels are tougher than most homeowners expect, and most hailstorms leave them unharmed. But golf-ball hail and larger can crack glass and cells, and the most expensive damage — micro-cracked cells — is invisible from the ground and shows up only as a slow drop in power output.
So after the storm: check the panels from the ground, check your production numbers, photograph anything that looks wrong, and write the storm details down while they’re fresh. If output dropped and the glass looks fine, ask for a professional inspection and an EL test — that’s the evidence that turns a hunch into a claim.
StormFile is a documentation tool — a timestamped, AI-assisted photographic record of visible condition. It is not an inspection, not an adjuster’s opinion, and not legal or insurance advice. For questions about coverage or your claim, talk to your agent or a licensed professional.